Thermal · Service
Energy recovery economics for cycling
What >90% regenerative feedback does and does not cover, and how to build a payback calculation from your own throughput and tariff.
Regenerative discharge is easy to describe and easy to overstate. The headline is that a module or pack system can return more than 90% of discharge energy to the grid instead of burning it in a resistor. The engineering question is what that percentage applies to, what it does not cover, and how to calculate the saving for a specific lab. This note separates the published number from the arithmetic you have to do yourself.
Where the energy goes
During charge, the system draws energy from the grid and stores it in the battery, with conversion losses. During discharge, a dissipative system turns the battery's energy into heat. A regenerative system converts the discharge energy back to grid-compatible AC and exports it, again with conversion losses. The published “>90% energy feedback” figure for module and pack systems refers to that discharge path. It is not a round-trip efficiency and it is not a statement about the charger's own consumption.
The distinction matters because the cell-level and module-level products do not publish the same number. The BTS-4008Q-5V20A-SR and BTS-4008Q-5V30A-SR cell-testers list a system efficiency above 65%, while the module and pack range is described as returning more than 90% of discharge energy. A cell tester with a 65% system efficiency and a pack system with >90% feedback are answering different questions. Do not carry one figure into a proposal for the other.
The arithmetic, with the assumptions exposed
Let E be the energy discharged in a cycle, η the fraction returned to the grid, and p the electricity price. The net energy drawn for the discharge half of the cycle is E(1 − η). A dissipative system draws nothing during discharge but rejects E as heat. The saving in purchased energy is therefore ηE, before cooling is considered.
The following example is illustrative, not a quotation or a measurement. Substitute your own throughput, tariff and cooling figures.
| Input | Illustrative value | Where to get your value |
|---|---|---|
| Discharge power | 400 V × 100 A = 40 kW | Pack voltage and test current |
| Discharge duration | 8 h/day | Utilisation plan |
| Discharge energy | 320 kWh/day | Power × duration |
| Feedback fraction | 90% | Published system figure; confirm at quotation |
| Recovered energy | 288 kWh/day | 320 × 0.90 |
| Net draw for discharge | 32 kWh/day | 320 × 0.10 |
| Electricity price | €0.15/kWh (assumption) | Your tariff, including taxes and network charges |
| Energy saving | €43.20/day (assumption) | 288 × your price |
All monetary values depend on the tariff you enter. The 90% figure is the published module/pack feedback claim, not a measured result from this example.
Cooling is the second saving
A dissipative discharge turns the discharged energy into heat inside the lab. At 40 kW continuous, that is 40 kW of heat that the HVAC system has to remove, plus the heat from the charger itself. A regenerative system removes most of that load at the point of conversion, so the cooling saving is proportional to the recovered energy, not to the whole discharge.
The cooling calculation needs the chiller or HVAC coefficient of performance (COP). If the cooling system moves three units of heat per unit of electrical input, the electrical cooling power is roughly the heat load divided by three. That is an engineering estimate, not a published product specification; use the COP of the actual installation. The point is that the saving appears twice — once on the electricity bill and once on the cooling bill — and the second one is often omitted from payback calculations.
What the percentage does not cover
Feedback efficiency is measured at the conversion stage. The site may not be able to accept export at all. Reverse-power protection, a transformer that is already loaded, a utility connection that forbids export, or a DC-bus architecture that returns energy only to another channel all change the calculation. Confirm the grid interface before assuming that the published percentage is realisable.
Power quality belongs in the same conversation. The platform publishes a power factor of 0.99 and THDi of 5% or less at full load on the high-current cell tester. A module or pack installation has its own input characteristics; ask for the figures for the exact model and confirm that the local network can accept them. Harmonics and reactive power are utility issues, not just instrument issues.
Battery limits are unchanged by regeneration. The BMS still sets the voltage, current and temperature limits, and the test system still has to respect them. Regenerative discharge does not allow a deeper discharge or a faster ramp; it changes where the energy goes, not what the cell can safely deliver.
Building the business case
Collect four numbers: annual discharge energy, the feedback fraction you can actually use, the all-in electricity price, and the cooling COP. Then add the cost of the regenerative option and any grid-interface work. Payback is the premium divided by the annual saving. If the result is close to the decision threshold, run the calculation at the low end of the feedback range and at a utilisation level you can defend; a business case that only works at 100% uptime is not a business case.
Keep the measurement honest after installation. A dedicated meter on the test-system feed, read over a full week, will show whether the calculated saving appears in practice. The meter also captures standby consumption and auxiliary loads that the headline percentage ignores.
Takeaways
- The published >90% figure for module and pack systems is a discharge-path feedback claim, not a round-trip efficiency; cell-testers such as the BTS-4008Q-5V20A-SR publish a different system-efficiency number.
- The saving is the recovered discharge energy plus the cooling load that is no longer rejected inside the lab; both depend on your tariff, utilisation and cooling COP.
- Check the grid interface, power quality and BMS limits before treating the percentage as cash — the conversion efficiency is only one term in the payback.
Request a configuration review
Tell us the channel count, current range and protocol. We will check the measurement class against the note and return a configuration, not a generic datasheet.
Request a configuration reviewReferences
- BTS-4008Q-5V20A-SR — datasheet (PDF)
- BTS-4008Q-5V30A-SR — datasheet (PDF)
- BTS-4008Q series
- BESS testing
- EV battery testing
- Peer-reviewed use of this instrument class: Alkaline-based aqueous sodium-ion batteries for large-scale energy storage — Wu (2024), Nature Communications. DOI: 10.1038/s41467-024-44855-6
- Module & pack test systems
- Calibration and service